Barbeque Use & Maintenance Tips
July 24, 2007
As the hot weather set in, gas and propane bbq's are fired up for the summer grilling season but before getting started it's important to ensure your barbeque is in fine working order:
ASSEMBLY - Take special note of every bolt hole illustrated on your assembly instructions. Proper placement will ensure it goes together right the first time. Also, over tightening your hex-bolts as you assemble will result in a squashed look to your bbq frame. Snug is good enough.
ALWAYS READ the safety and operating instructions before you begin to use your grill. Important topics include: Clearance of your bbq to combustibles, leak testing,
positioning of your wave sear plates, cleaning your grease tray and sear plates to avoid dangerous grease fires and positioning of gas supply lines to avoid melted hoses and
hazardous gas leaks.
ALWAYS REMOVE your warming rack before operating your rear burner. The intense heat of a rotisserie burner will surely destroy the warming rack.
PROPANE MODELS! Always have all valves in the OFF position before you turn on your propane tank. In addition, turn your propane valve open SLOWLY. Failure to follow either of the above will result in the regulator locking out at low BTU and therefore low heat. If your bbq is not getting hot enough to cook on properly, this may be your problem. To reset the regulator disconnect it from the tank for approx. 5 minutes, reconnect, and follow the correct procedure.
PREHEAT YOUR BBQ AND CLEAN YOUR GRILLS IN ONE EASY STEP!
Gasland recommends always preheating your bbq with all bottom burners turned on high for 8-12 minutes prior to cooking. This process:
A. Cooks off all the grease left behind from the last time you grilled, draining it towards the drip tray and preventing flare-ups.
B. Prepares your cooking grills to sear and seal in the juices of the meal you are about to cook.
C. It also cooks off the oils that bind the crud to your grill so all you have to do is remove the excess build-up off your grills with a WOODEN HANDLE brass brush or rod grill brush. Allow stainless grills to season to a black finish to prevent sticking. Scrubbing them back to silver is a waste of effort and conditioning. Once you have preheated your grill you may select your cooking zone and temperature to grill your meal to perfection!
GENERAL CLEAN UP:
2-3 times a year it is recommended that you give your bbq a thorough cleaning and service your burners. Follow the procedure stated in the preheat your bbq and clean your grills in one easy step section. Next, allow the housing to cool to the point that it is safe to touch, yet still warm enough that the grease and build-up looks wet or melted. Then simply remove your cooking grills, sear plates, and disposable grease tin.
Place a catch bucket under the area that your grease tin was and scrub your housing down with warm/hot soapy water and a nylon scrub brush. Use a good dish detergent with degreasing qualities such as Sunlight. Wipe off any excess water and you are ready to go.
When performing a thorough clean-up on your grill 2-3 times a year it is recommended that you service your burner. Scrub over the ports and
burner surface with steel wool or a small steel brush. Then clean the build-up from your burner holes by poking them clear with an unfolded paperclip or welding tip cleaner. Unlike low quality burners that develop larger holes and “Great Balls of Fire” as the burner erodes, heavy quality burners maintain their integrity. However, oxidation still builds up on the surface of the burner affecting performance. No burner can survive the harsh environment of heat, grease, sauces, and moisture without requiring regular maintenance.
IGNITOR & ELECTRODES:
Because of the harsh environment it is expected on all barbeques that the electrode and collector box of your ignition system may have to be replaced in 2-5 years if they erode or fail to perform. They are inexpensive and easy to replace.
RESTORE THE WOW TO STAINLESS STEEL:
Gasland offers two outstanding stainless cleaners by Continental to maintain the glamour of stainless steel housings. Our heavy duty cleaner #N003-0259 works like magic to remove stains and discoloration without working up a sweat. For the second step, bring back the original luster of your stainless steel removing fingerprints and smears with our 3M Polish Kit by Continental. This kit comes with a scotch brite pad to be used in the direction of the grain.
Article provided by Gasland Equipment and Fireplace
in Surrey, BC.
Return to Newsletter